More and more men prefer to cut their own hair: haircut and hair equation at home can save a lot of money. Though, that the benefits are obvious, not everyone knows, how to properly set up a hair clipper, to use it later without any problems. In today's article we will talk about the intricacies of setting up this type of device and consider some features of operation.
Why you need to adjust the machine
Many are wondering, and why regulate this, it would seem, simple device, because it can work without any regulation. So, can, but not for long, as with proper care for him. If you set up a hair clipper and periodically maintain it, performing simple routine work, it will last much longer and will not cause problems with minor breakdowns.
Some devices may over time become inconvenient to use, bite bundles of hair or fight with electricity. At the first signs of malfunction, the device should be serviced immediately.
Over time, unbalanced knives can leave some straight hair uncut, due to which the general look of a hairdress can suffer. In addition to possible malfunctions, adjustment may be required for comfort of operation. so, if you want to, so that the device lasts you a long time and does not bring unpleasant surprises, then a few recommendations should be followed.
Blade adjustment
Adjusting the blades of the hair clipper is a necessary procedure throughout the life cycle of the device. This is done only then, when it becomes apparent that the performance of the device is reduced (worse cuts, eats, jamming knives).
To adjust the blade of the device, it is necessary to thoroughly clean it from dirt, dust and fine hairs. From tools the simple screw-driver and in some cases a special sharpening board with several surfaces will be required.
Use a screwdriver to unscrew the screws, fixing the blades on the body. It is important to remember, that different manufacturers place the mounts in different places, but the principle itself always remains the same. Perform this procedure completely once, there should be no further difficulties.
Despite the general principle of regulation, differences still exist, therefore, a more detailed description of the manufacturer brands will be given below.
To begin with it is necessary to loosen fastening of bolts on the case, unscrewing both screws. The edge of the lower blade slides to the edge (right) upper. This position is fixed and set. Often this allows you to achieve the most optimal trimming of dense bristles of small length. In some cases, it may be necessary to fix on the left edge or even in the middle.
There is also a simpler setup of machines, without focusing on corners. The process is exactly the same, but with one difference: the label is the middle of the upper blade. This regulates most modern electric machines of the budget level.
If the appliance has been used for a long time, probably, you will need to lubricate the metal parts in order, to keep them as long as possible. In most cases, it is enough to expose the blade once, and the hair clipper will work again for a long time, until the next service. To prolong the life of the knives, you should clean them of dirt and small hair after each haircut, as well as wipe thoroughly, so that moisture does not get inside the case.
Examples of knife adjustment (video)
If difficulties in adjusting the blades still remain, you can refer to video tutorials on balancing them.
Video on the topic of adjusting hair clippers Vitek:
Feature: it is best to leave a small gap between the upper and lower knife. This will optimize the operation of the device and eliminate jams during operation. Do not tighten the bolts too much, to eliminate the possibility of thread breakage. If the thread is damaged, the adjustment of the blades will be much more complicated, or even impossible.
Here's how to best adjust your Moser:
Feature: the machine will work best, if at adjustment to expose blades so, that the extreme tooth of a small knife slightly went for a tooth of a big blade. Machines of this brand have a strong thread, in which the blades are fastened screws, but it is still not necessary to twist them to the stop.
Domotec devices are better to regulate everything this way:
Feature: before installing the blades it is best to lightly grind them on a grinding board, using the lapping side. Do not forget to slightly moisten the surface of the board with water. If necessary, the procedure should be repeated, until the blades are finalized. Unbalance occurs under constant vibration under load and touch (friction) metal surfaces.
The following steps are fully applicable to Skarlett machines:
Feature: many models are adjustable without removing the blades, by simply tightening the mounting bolts. In some cases, you may need to lubricate the used parts. For a basis it is better to use oils of new generation on the basis of hydrocracking additives or usual motor oil.
Machines from this manufacturer require more frequent adjustment. However, the process itself is significantly simplified compared to models of other brands, so it will not be difficult to do such service.
The nuances of caring for technology
It is worth paying attention to the common criteria for the care of technology.
-
- Before servicing the appliance, the operating instructions should be read. There is intelligible and clear (in addition, step by step) the whole maintenance process is shown.
- Don't do anything, if you are unsure or afraid to break the device.
- If the device is used during the year, the use of lubricating iron parts lubricants is necessary, T. To. the factory base has already been developed.
- In case of long operation, or if the machine is used frequently, additional grinding of blades may be required. To do this, you need to buy a grinding board with different surfaces.
- Under no circumstances should the blades be fixed by force. If the knives do not rise to the desired position, there is a probability, that something was done wrong, perhaps, you should read the instructions again or look for additional information. Some models come with a special locking key. Truth, is quite rare, therefore experts recommend to use usual screw-drivers, which are in every home.
- If adjusting the blades did not help, perhaps, should be replaced. New knives are much cheaper, than the whole tool assembly. Many modern hair clippers are unified, and suitable nozzles and blades can be installed on them.
It is very easy to use a hair clipper. You can also easily take care of her. Adjusting the knives will not take much time, but such a simple action often helps to breathe a second life into the device, which until recently seemed faulty. Everything, What you need, it's a little patience and perseverance. In the future, this process will take very little time. Besides, having adapted to service one model, you can get the skill to adjust the blades on most modern hair clippers.