Compensation pipe and other sewer fittings

Fittings for the sewerage from polyvinylchloride (Pvc) - these are shaped elements, which are used in the installation of sewer structures and perform the function of connecting elements. By means of these products joining of separate elements of sewer systems is carried out, as well as their repair. One of the ways to repair the drain pipe is to install a compensation pipe.

The compensating branch pipe is a fitting, which is applied, mainly, to replace part of the system

Feature of sewer fittings made of PVC

Today, pipes for sewer systems are made of modern polymeric materials, such as: polyethylene (PE) and polyvinyl chloride (Pvc). Shaped parts of sewer pipes are also made of these materials. Polyvinyl chloride sewage pipelines are considered to be the most popular, since they have many advantages over others (especially if you compare them with old cast iron sewer structures).

pay attention! Use of PVC fittings allows to carry out installation of the sewerage quickly and without special difficulties, as this does not require welding equipment or other specialized tools.

It is safe to say that, that the use of fasteners made of this material not only improves the performance of the mounting system, but also increases its "shelf life" in general.

The most popular such connecting details at installation of designs of sewer in apartments and private houses. PVC fittings have a long-term heat resistance of no more, than 80 °C. exept this, they can withstand short-term exposure to temperature 95 °C. Pipes and fittings made of this material can transport not only drains, but also chemicals. Chemical substances, transported by such pipelines, have a certain pH range (from 2 to 12).

Fittings for PVC pipes - common parts on the market, which are available in a fairly wide range

Advantages of using PVC fittings

PVC sewer fittings have many advantages, which distinguish them from other materials:

• light weight. This advantage is considered one of the main, as small weight of shaped elements from polyvinylchloride provides fast installation of a sewer design without special expenses. Installation of polyvinyl chloride products can be done alone. The light weight of these devices simplifies their transportation;
• long service life. Shelf life of such products, usually, is not less 30 years (in some cases more);
• high rate of resistance to harmful corrosion;
• resistance to aggressive chemical compounds;
• high coefficient of moisture resistance;
• smooth inner walls. Thanks to perfectly smooth internal walls products from polyvinylchloride are not subject to overgrowth because of accumulation of salt deposits.;
• ease of installation. Labor costs when installing a sewer system with PVC fittings are minimized. Sewer construction of this kind is mounted on the model of the designer (the edge of the first pipe is put on the edge of the second).
• the ability to mount a structure of almost any configuration.

Polyvinyl chloride products are popular and easy to assemble and, exept this, have high performance characteristics. Reliability and long service life are the two main guarantees, which are inherent in products made of this material.

PVC pipe products are easy to assemble, because they have bells, and tightness is provided by rubber seals

Types of sewer PVC fittings

All sewer fittings made of polyvinyl chloride are divided into two main types, depending on, where exactly their installation is performed:

• fittings for internal sewerage;
• for external sewer communication;

Useful Information! The first type includes products, installed inside apartments and private homes, as well as other buildings. The purpose of internal sewerage communication is to transport sewage to external sewerage, which performs the function of their removal to treatment facilities. Pipes and fittings of the external sewer system are installed outdoors.

There are two main types of polyvinyl chloride fittings:

• by means of a rubber sealing element (gaskets);
• with glue. In this case, the joint is made without a sealing ring.

Almost all connecting parts are made of polyvinyl chloride, usually, are mounted using a rubber seal. This allows you to achieve the required level of sealing joints.

PVC fittings for internal sewers

Varieties of polyvinyl chloride fittings for internal sewerage, are mounted by means of a rubber sealing element:

• clutch. Connecting detail, which is made of PVC and is used for joining pipes on an equal section of the pipeline. There are two types of couplings for internal sewer communications: with emphasis, full bore (used in repairs);
• reduction. This is a connecting part, which is used to organize transitions between pipes with different cross-sectional indicators. exept this, it is also used to connect pipes of different materials (example, for joining PVC and cast iron);

Different types of fittings are used to install the system, allowing you to change the direction of the system, branch it, unimpeded repair and maintenance during operation

• revision. Equipped with a lid and used in the case, if cleaning measures are planned;
• tee. Popular fitting, which is used to connect the auxiliary branch to the main sewer line. The most popular tees, which have the following angles: 45, 90°;
• cross-piece (with one or two planes). Connecting detail, for joining four pipes together. The sewer crosspiece can have different diameters of branch pipes, for joining of pipes with various indicators of section;
• plug. Used to block a deaf area of ​​sewer communication.
• challenge. This is a device, which is used to branch the sewer at a certain angle. Usually, these angles are 30, 35 and 90 °.

PVC fittings for external sewerage

The same fittings are used for the external sewer network, as for internal, however, there are some differences in their structure. Docking of such products is also performed using a rubber seal. so, consider the types of fittings for external sewerage and their features:

• challenge. The branch for the external sewerage differs in that, which has a greater variety of angles. With the help of such a connecting element, you can arrange the reversal of the pipe on: 15, 30, 45, 67, 90°;
• branch two-trumpet. Product, each side of which is equipped with rubber sealing elements;
• clutch. In this case, it is represented by only one species;
• tee. It differs in that, that its angle is always equal to 90 °. The tee for an external sewer network can be three-bell;

Fittings for external systems have the same principle of assembly, as for domestic, but some details have design differences

• cross-piece (uniplanar). Always located at right angles, as well as a tee;
• check valve. This fitting is mounted on a horizontal sewer line, the slope of which does not exceed 2 cm per meter;
• two-piece siphon.

When installing an external sewer, it is very important to choose the right connecting elements. This is necessary to organize the branches and perform the required slope of the system.

Fittings, mounted with glue

Such types of fittings are mounted by means of glue:

• clutch;
• challenge, with which you can organize the rotation of the system on 30, 45, 87, 90°.
• tee, which is mounted on glue and has angles of rotation, corresponding to a similar figure in the tee for internal sewer construction;

Useful Information! Connecting products, which are established by means of special glue structure, can be operated for internal and external sewer communications.

• reduction;
• audits;
• cross-piece (biplane), which has angles 45 and 90 °;
• cap for glue;
• nurse. This is a special connecting device, used for insertion into the main riser. This element can be equipped with a bell, located at an angle of 90 °.

What is a compensation pipe

This product is used to repair sewer structures inside residential areas, industrial and other structures. The compensating branch pipe is mounted on a place of the cut out (broken) areas of communication. It is connected to the pipe by means of a connecting socket on one side, and on the other - by means of one more connecting element - couplings. Such sewer pipes are considered to be very popular products and are also equipped with rubber sealing elements..

Compensation pipe is used in internal sewer systems

This product has an elongated bell, which allows you to place the pipe in it quite deeply, regardless, vertically located system or horizontally. Such a pipe is also needed to compensate for thermal expansion, which can cause deformation and destruction of the sewer system.

Features of installation of PVC fittings for the sewerage

For correct installation of a sewer design by own hands it is necessary to get acquainted with features of use of separate elements, as well as installation rules. Here are some helpful tips, thanks to which it is possible to avoid problems at laying of this communication. Consider them:

• PVC pipes must be cut with a special hacksaw (on metal). Preferably, so that the teeth on the canvas are small. This is necessary for that, to get the smoothest possible cut, without protruding plastic pieces;
• after cutting the pipes into segments of the required size, it is recommended to process their ends. The ends should not have burrs, be rough. You can use sandpaper for this. Preparation of the ends will contribute to a denser shrinkage of the fitting. exept this, during operation, well-cleaned parts minimize the risk of leakage;
• the ends when stripping should not be wet;

Pipe joints with fittings must not have any voids. If voids are present, it is recommended to process their sealing composition, to avoid leakage of the problem area during operation.

Step-by-step installation of the connecting fitting, which has a rubber sealing ring, such:

1. First of all, the coupling must be cleaned of dust.
2. You need to make sure of that, that the rubber sealing ring is located correctly.
3. In the third stage, it is recommended to use a marker. You will need it for that, to mark the depth of the PVC pipe, on which the connecting element will be mounted.
4. Then on the inner surface of the fitting it is necessary to apply a sealing material based on silicone. It is recommended to carry out this work carefully, as excessive consumption of sealing material will affect the financial costs.
5. At the last stage it is necessary to connect the sewer fitting with the pipe. Docking is carried out along the previously specified marker line.

Working with PVC fittings is not difficult, but all actions must be done carefully, especially with adhesive parts.