Iron alloy, containing carbon, called cast iron. In some cases, alloying additives are added to the composition, affecting its consumer qualities.
Cast iron is a metal, which is used primarily in ferrous metallurgy. Not only steel is obtained from it, it is also in demand in the manufacture of forged artistic details.
Gray cast iron is mainly used for mechanical engineering, containing graphite. Details, made of such material, do not respond to emerging stresses, they absorb fluctuations, which appear in case of vibration of mechanisms.
As a construction material it began to be used in almost all enterprises of the machine-building industry.
Details of tractors, the material of which was gray cast iron, reach 20% from the whole number of its details. This use of this alloy is associated with high wear resistance. It does not come off in the case of high friction and lack of oil, in other words, has damping ability.
Cylinder liners are used for car engines of any design, made of a special alloy. In most cases, its phosphorus fraction is used.
Diesel engines at work create a large load on the cylinder block, therefore, they use alloyed cast iron. Cylinder heads are made of high-carbon alloy grades,
The same requirements are observed in the manufacture of sleeve castings, the material of which is a low-alloy alloy.
Cast iron camshafts are installed on cars, characterized by high wear resistance. This parameter is achieved through surface hardening, to which the metal is subjected.
When the part is operated at high speeds, when there is dry friction, it is necessary to increase the wear resistance of the material and a high coefficient of friction. It is in such conditions that this alloy is simply irreplaceable.
Brake drums, working in such conditions, made of SC20. When the part is experiencing high loads, and the possible occurrence of thermal cracks, use a special heat-resistant alloy with a high carbon content and a high level of alloying.
For particularly difficult conditions, install the details, the material of which is pearlitic cast iron. It contains vermicular graphite.
The flywheel rotates during operation 7000 about / min. This speed causes the appearance of stresses, stretching. The rotating surface of the flywheel constantly touches the working surface of another part. Such friction causes a strong release of heat resulting in thermal cracks, which adversely affect the strength of the part.
It must ensure the strength of the workpiece above 250 N / mm2. Sometimes the middle 35 has strength, which is not enough to ensure the normal operation of the flywheel. In this case, use cast iron, where spherical graphite is added.
Cars boast cast iron covers, which close the main bearings. This design is found in most cases on cars with a carburetor engine. To provide a pearlitic structure, as well as high hardness, exceeding 200 NV, for the manufacture of bearing caps, apply SC25.
Exhaust gases act on the exhaust manifolds in the car, whose temperature reaches 90 degrees. Collectors are oxidized under the influence of aggressive environments, deform and crack.
The use of gray cast iron ensures the durability of such parts and high efficiency. Due to that, that the thickness of the collector walls is very small, Less 7 mm, for their manufacture apply SCh15. To increase its heat resistance, carry out alloying of cast iron with chromium, or nickel additives.
All the above materials have high heat resistance and resistance to aggressive environments, alkalis and oxides.
A large number of cast parts are made of gray cast iron in machine tool construction, working in all sorts of conditions, the mass of which can reach 100 tons, at the maximum wall thickness 200 millimeters.
Classification of such cast parts in machine tool construction, depending on the designs, from the arisen operating conditions corresponds to the current standard.
Given the specifics of many machine tool parts, which work mainly on rigidity, for their manufacture it is better to use cast iron, having increased hardness, rather low plasticity.
In such cast irons, the chemical composition is high in manganese, and low carbon. To obtain high hardness of cast iron, use alloying and other technological processes.
A lot of cast iron products are used in plumbing. Made of cast iron:
And today cast iron baths remain in demand, which are characterized by high strength, durability and reliability. Such products can be operated for decades. They retain their original appearance and do not require replacement.
Craftsmen make artistic masterpieces from cast iron. Example, embankments of St. Petersburg, decorated with cast iron details. Walking through the streets of the city you can meet the openwork gates, original cast iron fences. Cast iron monuments can be seen in the squares.
This material has excellent damping ability, it is able to work effectively at very low temperatures. This type of cast iron is used in the manufacture of critical parts of tractors, as well as cars, who will have to do their job in difficult climatic conditions.
Such products perfectly cope with power loads, they can bend under mechanical impact.
In other words, for details, under heavy static loads, subject to friction and rapid wear. Antifriction malleable cast iron is used for such products, able to create minimal friction, there, where there is a maximum contact of details.
Gas systems use malleable cast iron to make fittings, connecting pipes, where there are various branches.
Various brands of ductile iron are widely used in landscaping, when the formation of decorative details:
Mankind has been using cast iron for many centuries, today almost everyone is dealing with such an alloy. It has high strength and relatively low cost. The only disadvantage of cast iron parts is their fragility. But, with the right technology for producing cast iron, this shortcoming is minimized, that is why cast iron parts are so widely used in the above industries.
A sewing machine is an indispensable tool for many housewives.. Ее наличие среди бытовых принадлежностей дает возможность…
Fuel truck - special equipment, which is intended for the transportation of refined products and fuels and lubricants. Она представляет…
If you are determined to learn the acoustic guitar, варто одразу купувати якісну продукцію в надійному…
Face masks are one of the most popular face care products.. After all, они становятся…
"The key to a woman's heart is an unexpected gift at the wrong time", - says Forrester in the film "in…
Modern hairpins can not only fulfill their immediate obligations, но и сделать образ девушки индивидуальным…